Galvanized Screw Pin Chain Shackles

galvanized-screw-pin-chain-shackles-front_md.jpggalvanized-screw-pin-chain-shackles-side_md.jpg
 
GALVANIZED SCREW PIN CHAIN SHACKLES
SIZE IN INCHES WORKING LOAD LIMIT IN TONS PIN DIAM. IN INCHES DIMENSIONS APPROX. WEIGHT EACH IN POUNDS
 (A)   (B) C D E  
1/4 1/2 5/16 .88 .50 .63 .09
5/16 3/4 3/8 1.00 .53 .78 .17
3/8 1 7/16 1.28 .69 .97 .32
1/2 2 5/8 1.72 .84 1.28 .80
5/8 3.1/4 3/4 2.03 1.06 1.50 1.3
3/4 4.3/4 7/8 2.41 1.25 1.81 2.2
7/8 6.1/2 1 2.91 1.72 2.13 3.2
1 8.1/2 1.1/8 3.25 1.75 2.38 5.1
1.1/8 9.1/2 1.1/4 3.56 1.81 2.63 6.5
1.1/4 12 1.3/8 3.97 2.00 2.91 9.0
1.3/8 13.1/2 1.1/2 4.56 2.19 3.25 12.2
1.1/2 17 1.5/8 5.00 2.34 3.50 17.0
1.3/4 25 2 6.00 2.88 4.38 25.5
2 35 2.1/4 7.00 3.31 4.91 37.0
2.1/2 55 2.3/4 8.00 4.13 5.88 75.0
3 85 3.1/4 8.25 5.25 6.75 108.0

 

According to Federal Specification RR-C-271D, Type IV B, Class 2, Grade A.
Hot galvanized, forged carbon steel, heat treated, with oversized pins, permanently marked with size and Working Load Limit.
Do not use screw pin shackles if the pin can roll under load and unscrew.
CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT.
WARNING: Read important warnings and safety information.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Oblong Master Links Grade 80

According to ASTM A9527A906. Welded, painted.

OBLONG MASTER LINKS, ALLOY – Grade 80 heat treated, painted red

DIAMETER IN INCHES -D- WORKING LOAD LIMITS IN POUNDS (SINGLE PULL) DIMENSION IN INCHES APPROX. WEIGHT EACH IN POUNDS ESI PART # ‘s
-W-
WIDTH
-F-
FLAT
-L-
LENGHT
1/2 4,100 2 3/4 9 3/2 4/34 0.8 12G80OML
5/8 5,500 3 9 3/2 4 3/4 1.6 58G80OML
3/4 8,600 3 3/4 7/16 6 1/4 2.4 34G80OML
1 20,300 4 5/8 1/2 7.12 5.0 1G80OML
1 1/4 29,300 5 1/8 5/8 9 10.5 114G80OML
1 1/2 39,900 5 1/4 - 10.5 16.5 112G80OML
1 3/4 52,100 6 - 12 28.2 134G80OML
2 81,400 7 - 14 32.0 2G80OML
2 1/4 99,400 8 - 16 53.0 234G80OML
2 1/2 122,750 8 - 16 69.0 212G80OML
2 3/4 148,500 9 - 16 97.0 234G80OML
3 190, 10 - 19 136.0 3G80OML
3 1/2 232,500 12 - 24 198.0 312G80OML

All oblong master links are individually proof tested to two times the higher of the maximum working load limits
listed for that size – as a minimum.

All oblong master links meet the requirements of ASTM A952 – standard specification for forged grade 80 alloy
steel lifting components and welded attachment links and the mechanical requirements of ASTM 906, standard

WARNING: Read important warnings and information on sections Wire Rope and General Information on Wire Rope and preceding wire rope section.

According to ASTM A952/A906. Welded, painted
All oblong master links meet the requirements of ASTM A952- standard specification for forged Grade 80 alloy steel lifting components and welded
attachment links and the mexhanical requirements of ASTM 906, standard specification for alloy steel chain slings for overhead lifting- as applicable.
All oblong master links are individually proof tested to two times the higher of the maximum working load limits listed for that size as a minimum.
CAUTION: Do not use for overhead lifting. Never exceed working load limit.
WARNING: Read important warnings and safety information.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Sling Links Grade 43

PEAR SHAPED SLING SLINKS- Hegh Test, Heat Treated
SIZEIN INCHES DIMENSIONS IN INCHES WORKING LOAD LIMIT IN POUNDS APPROX.WEIGHT EACH IN POUNDS
L W1 W2 (SINGLE PULL)
3/8 2.25 1.50 .75 1,800 .23
1/2 3.00 2.00 1.00 2,900 .51
5/8 3.75 2.50 1.25 4,200 1.1
3/4 4.75 2.75 1.38 6, 2.0
7/8 5.25 3.50 1.75 8,300 2.7
1 6.00 3.75 1.88 10,800 4.6
1.1/4 8.00 5.00 2.50 16,750 9.0
1.3/8 8.25 5.50 2.75 20,500 11.6
1.1/2 9.25 6.00 3.00 25, 15.0
1.3/4 10.50 7.00 3.50 34, 23.1
2 12.50 8.00 4.00 45, 33.0
2.1/4 14.00 9.00 4.50 56, 47.3
2.1/2 15.50 10.00 5.00 68,500 67.0
2.3/4 17.00 11.00 5.50 84,500 93.0

3/8″ through 1.1/4″ forged, larger sizes welded. Heat treated. Painted or Hot Galvanized, Grade 43.
Sizes 3/8″ through 1.3/8″ carbon steel.
Working Load Limit based on 6 times the Minimum Ultimate Breaking Strength. Proof Load tested.
CAUTION: Do not use for overhead lifting. Never exceed working load limit.
WARNING: Read important warnings and safety information.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Grade 80 Clevis Sling Hook

 CLEVIS SLIP HOOK- Grade 80, Forged Alloy Steel, Heat Treated, Painted, with Steel Latch
SIZE IN INCHES DIMENSIONS IN INCHES WORKING LOAD LIMIT IN POUNDS APPROX. WEIGHT EACH IN POUNDS
  A B C D    
9/32 .34 .35 1.00 3.40 3,500 2.21
3/8 .48 .51 1.20 4.13 7,100 2.43
1/2 .60 .63 1.61 5.06 12, 4.30
5/8 .75 .83 1.97 6.11 18,100 7.49
3/4 .83 1.02 2.36 7.24 28,300 12.12

 

 

 

 

 

 

CAUTION: Never exceed working load limit. Do not use for overhead lifting.
WARNING: Read important warnings and safety information.

 


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Proof Coil Chain Grade 30


All chains manufactured to NACM 90 and or ASTM 80 Specifications. Tested and certified.


PROOF COIL CHAIN - Self colored, zinc plated, hot galvanized

SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM FEET PER 1/2 DRUM FEET PER PAIL MINIMUM WEIGHT PER FOOT
1/8 375 1, 500 - 0.17
3/16 750 1,500 760 250 0.33
1/4 1,250 800 400 141 0.63
5/16 1,900 550 275 92 0.93
3/8 2,650 400 200 63 1.41
1/2 4,500 200 100 35 2.4
5/8 6,900 150 75 - 3.58
3/4 9,750 100 50 - 5.48
7/8 11,375 75 35 - 7.31
1 13.95 60 30 - 9.41


6 X 25 STAINLESS STEEL WIRE ROPE*

FEET PER DRUM ESI PART #’S (FULL DRUM)
SELF COLORED ZINC PLATED HOT GALVANIZED
1, - - 18HG28
1,500 316SC28 316EG28 316HG28
800 14SC28 14EG28 14HG28
550 516SC28 516EG28 516HG28
400 38SC28 38EG28 38HG28
200 12SC28 12EG28 12HG28
150 58SC28 58EG28 58HG28
100 34SC28 34EG28 34HG28
75 78SC28 78EG28 78HG28
60 1SC28 1EG28 1HG28
FEET PER 1/2 DRUM ESI PART #’S (HALF DRUM)
SELF COLORED ZINC PLATED HOT GALVANIZED
500 - - 18HG28
760 316SC28 316EG28 316HG28
400 14SC28 14EG28 14HG28
275 516SC28 516EG28 516HG28
200 - 38EG28 38HG28
100 - 12EG28 12HG28
75 - 58EG28 -
50 - 34EG28 -
35 - 78EG28 -
30 - 1EG28 -


6X19 FIBER CORE IPS (CHINESE)
SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM FEET PER 1/2 DRUM MINIMUM WEIGHT PROOF ESI PART # ‘s
SELF COLORED HOT GALVANIZED SELF COLORED HALF DRUMS
1/4 2,600 800 400 0.63 14SC43 14HG43 14SC43
5/16 3,900 550 275 0.93 516SC43 516HG43 5116SC43
3/8 5,400 400 200 1.41 38SC43 38HG34 38SC43
1/2 9,200 200 100 2.4 12SC43 38HG34 -
5/8 13, 150 75 3.58 58SC43 58HG43 -
3/4 20,200 100 50 5.48 34SC43 34HG43 -

Note: these figures are for comparison purposes only. Please refer to the charts for exact figures.


PROOF COIL CHAIN
- Self colored, zinc plated, hot galvanized


LONG LINK CHAIN – Galvanized
SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM IN INCHES INSIDE LENGTH IN INCHES INSIDE WIDTH MIN. WEIGHT PER FOOT IN POUNDS ESI PART # ‘s
1/2 4,500 200 3.50 0.798 2.22 12HG28LL
5/8 6,900 150 3.75 1.00 3.41 58HG28LL
3/4 9,500 100 3.75 1.125 4.20 34HG25LL

Note: these figures are for comparison purposes only. Please refer to the charts on page for exact figures.

CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT OF CHAIN. NEVER USE PROOF COIL CHAIN
FOR OVERHEAD LIFTING OR WHERE ITS FAILURE WILL CAUSE DAMAGE TO PROPERTY OR LIFE.

PROOF COIL CHAIN GRADE 30
SIZE IN INCHES WORKING LOAD LIMIT IN POUNDS FEET PER DRUM FEET PER 1/2 DRUM MINIMUM WEIGHT PER FOOT
1/8 400 —- 1, .17
3/16 800 1500 750 .33
1/4 1,300 800 400 .63
5/16 1,900 550 275 .93
3/8 2,650 400 200 1.41
1/2 4,500 200 100 2.40
5/8 6,900 150 75 3.58
3/4 10,600 100 50 5.48
7/8 12,800 75 35 7.31
1 17,900 60 30 9.41
PROOF COIL CHAIN GRADE 30 – DEALER PAILS
SIZE IN INCHES WORKING LOAD LIMIT IN POUNDS FEET PER PAIL, APPROX.
3/16 800 250
1/4 1,300 141
5/16 1,900 92
3/8 2,650 63
1/2 4,500 32
LONG LINK CHAIN GRADE 30 – LONG LINK CHAIN
SIZE IN INCHES WORKING LOAD LIMIT IN POUNDS FEET PER DRUM IN INCHES INSIDE LENGTH IN INCHES INSIDE WIDTH MIN. WEIGHT PER FOOT IN POUNDS
1/2 4,500 200 3.50 .798 2.22
5/8 6,900 150 3.75 1.00 3.41
3/4 9,500 100 3.75 1.125 4.20

All chains manufactured to NACM 90 and or ASTM 80 Specifications. Tested and certified.
Half drums and dealter pails available in zinc plated and hot galvanized. Also available in ASTM Specification.
Upon request, NACM 96 available.

CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT OF CHAIN. NEVER USE PROOF COIL CHAIN FOR OVERHEAD LIFTING OR WHERE ITS FAILURE WILL CAUSE DAMAGE TO PROPERTY OR LIFE.
WARNING: Read important warnings and safety information.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Grade 70 Transport Chain


TRANSPORT CHAIN – Grade 70, yellow chromate finish


6X19 FIBER CORE IPS (CHINESE)
SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM MINIMUM 1/2 DRUM WEIGHT FOOT IN POUNDS ESI PART # ‘s
1/4 3,150 800 400 0.63 14SCG70C
5/16 4,700 550 275 0.93 516SCG70C
3/8 6,600 400 200 1.41 38SCG70C
1/2 11,300 200 100 2.4 12SCG70C
5/8 15,800 100 - 3.75 58SCG70C

Also available in ASTM dimensions.


TRANSPORT CHAIN – Grade 70, yellow chromate finish

SIZE WORKING LOAD LIMIT IN POUDS APPROX. WT. EACH IN POUNDS ESI PART # ‘s
5/16 X 20′ 4,700 20.00 516SCG70BC20
3/8 X 20′ 6,600 31.00 38SCG70BC20
1/2 X 20′ 11,300 57.00 12SCG70BC20


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Alloy Chain Grade 80

Only grade 80 alloy chain can be used for chain slings for overhead lifting. Refer to OSHA standard 1910.184
and ASME standard B30.9 for design factors and other important information.

ALLOY CHAIN-GRADE 80


6X19 FIBER CORE IPS (CHINESE)
SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM MINIMUM WEIGHT PER FOOT IN POUNDS ESI PART # ‘s
9/32 3,500 800 0.71 932G80CH
5/16 4,500 500 0.92 516G80CH
3/8 7,100 500 1.44 516G80CH
1/2 12, 300 2.36 516G80CH
5/8 18,100 200 3.76 516G80CH
3/4 28,300 100 5.5 34G80CH
7/8 34,200 100 7.12 78G80CH
1 47,700 100 9.65 1G80CH
1 1/4 72,300 60 15.75 11480CH

Only Grade 80 must be used together with accessories or attachments having at least the same Working Load
Limit as the chain used.

CHAIN SLINGS

Only grade 80 alloy chain can be used for chain slings for overhead lifting.

Refer to OSHA standard 1910.184, ASME standard B30.9, and ASTM A906 specification for design factors
and other important information, Other standards and information may apply. Refer to page 5 for a discussion of chain slings.

Chain is 100 proof tested to 2x the Working Load Limit.
Working load limit is based on single led Grade 80 alloy sling, when utilizing Grade 80 or above attachments.
Only grade 80 alloy chain can be used for chain slings for overhead lifting. Refer to OSHA standard 1910.184 and ASME standard B30.9 for design factors and other important information.

CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT OF CHAIN. NEVER USEPROOF COIL CHAIN FOR OVERHEAD LIFTING OR WHERE ITS FAILURE WILL CAUSE DAMAGE TO PROPERTY OR LIFE.
WARNING: Read important warnings and safety information.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Alloy Eye Hoist Hooks Grade 80


EYE HOIST HOOKS – Grade 80 Alloy, Painted red with stainless steel latch

WORKING LOAD LIMIT IN POUNDS DIMENSIONS APPROX. WEIGHT EACH IN POUNDS ESI PART #’S (CARBON)
A B C D E F G H J K L M N
1 1.50 0.75 0.38 0.88 0.63 0.94 2.88 0.75 4.38 3.25 3.25 3.25 3.25 0.60 AEHH1T
1 1/2 1.75 0.88 0.44 1.00 0.69 1.06 3.13 0.81 4.88 3.63 3.63 3.63 3.63 0.82 AEHH1.5T
2 2.00 1.13 0.44 1.19 0.81 1.06 3.50 1.00 5.50 4.13 4.13 4.13 4.13 1.44 AEHH2T
23 2.38 1.25 0.59 1.38 0.94 1.22 3.94 1.19 6.31 4.56 4.56 4.56 4.56 1.94 AEHH3T
4 1/2 3.00 1.56 0.69 1.63 1.19 1.50 5.00 1.50 7.94 5.75 5.75 5.75 5.75 3.96 AEHH4.5T
7 3.81 2.00 0.88 2.06 1.50 1.88 6.25 1.75 10.00 7.38 7.38 7.38 7.38 7.75 AEHH7T
11 4.69 2.44 1.13 2.63 1.63 2.25 7.56 2.25 12.44 9.06 9.06 9.06 9.06 13.00 AEHH11T
15 5.37 2.84 1.26 2.94 2.19 2.51 8.30 2.59 13.93 10.07 10.07 10.07 10.07 10.00 AEHH15T
22 6.64 3.50 1.58 3.50 2.69 3.30 10.30 3.00 17.08 12.50 12.50 12.50 12.50 16.80 AEHH22T

Working Load Limit applies only when the load is applied to the center of the saddle of the hook.
CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT.

View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

High Test Chain Grade 43


All chains manufactured to NACM 90 and or ASTM 80 Specifications. Tested and certified.


PROOF COIL CHAIN - Self colored, zinc plated, hot galvanized


6X19 FIBER CORE IPS (CHINESE)
SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM FEET PER 1/2 DRUM MINIMUM WEIGHT PROOF ESI PART # ‘s
SELF COLORED HOT GALVANIZED SELF COLORED HALF DRUMS
1/4 2,600 800 400 0.63 14SC43 14HG43 14SC43
5/16 3,900 550 275 0.93 516SC43 516HG43 5116SC43
3/8 5,400 400 200 1.41 38SC43 38HG34 38SC43
1/2 9,200 200 100 2.4 12SC43 38HG34 -
5/8 13, 150 75 3.58 58SC43 58HG43 -
3/4 20,200 100 50 5.48 34SC43 34HG43 -

Note: these figures are for comparison purposes only. Please refer to the charts for exact figures.


HIGH TEST BOOMER CHAIN (GRADE 43)
High Test chain with grab hook each end.

WIRE ROPE DIAMETER IN INCHES LENGTH IN INCHES WORKING LOAD LIMIT IN POUNDS GRADE NO. OF LINKS APPROX. WEIGHT EACH IN POUNDS ESI PART #’S
3/8″ 18 5,400 High Test 13 5 38X18G43TC

TAIL CHAIN (WINCH LINE END CHAIN) – Use same size chain
Clevis grab hook and pear shaped link one on end.

CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT OF CHAIN. NEVER USE PROOF COIL CHAIN
FOR OVERHEAD LIFTING OR WHERE ITS FAILURE WILL CAUSE DAMAGE TO PROPERTY OR LIFE.

Self Colored or Hot Galvanized.

HIGH TEST CHAIN – GRADE 43
SIZE IN INCHES WORKING LOAD LIMIT IN POUNDS FEET PER DRUM FEET PER 1/2 DRUM MINIMUM WEIGHT PER FOOT
1/4 2,600 800 400 .63
5/16 3,900 550 275 .93
3/8 5,400 400 200 1.41
1/2 9,200 200 100 2.40
5/8 13, 150 75 3.58
3/8 20,200 100 50 5.48

HIGH TEST BOOMER CHAIN – GRADE 43 (GRAB HOOK BOTH ENDS)
SIZE WORKING LOAD LIMIT IN POUNDS APPROX. WEIGHT EACH IN POUNDS
1/4″ x 20ft. 2,600 13.5
5/16″ x 20ft. 3,900 20.0
3/8″ x 20ft. 5,400 30.5


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Alloy Chain Grade 120

ALLOY CHAIN – GRADE 120
SIZE IN INCHES WORKING LOAD LIMIT IN POUNDS FEET PER DRUM FEET PER 1/2 DRUM MINIMUM WEIGHT PER FOOT
9/32 5,200 800 400 .77
3/8 10,600 400 200 1.51
1/2 17,900 200 100 1.53

CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT OF CHAIN. NEVER USEPROOF COIL CHAIN FOR OVERHEAD LIFTING OR WHERE ITS FAILURE WILL CAUSE DAMAGE TO PROPERTY OR LIFE.
WARNING: Read important warnings and safety information.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

G 4 Windlass Chain

G-4 WINDLASS CHAIN – Hot dipped galvanized and stainless steel type 316, stamped "G4" on links.

This is a high tensile (Grade 43) chain especially calibrated for use on chain windlass.

SIZE OUTSIDE LENGTH OUTSIDE WIDTH INSIDE LENGTH INSIDE WIDTH
1/4 1.39 0.96 0.84 0.41
5/16 1.69 1.16 1.03 0.50
3/8 2.00 1.39 1.22 0.60
1/2 2.61 1.59 1.59 .0.77
5/8 3.21 1.79 1.79 0.91

 


HOT DIPPED GALVANIZED

CHAIN SIZE WORKING LOAD LIMIT WEIGHT PER FOOT IN POUNDS ESI PART # ‘s
1/4 2,600 0.73 14BBB40
5/16 5,900 1.1 516BBB40
3/8 8,100 1.6 38BBB40
1/2 1,800 2.69 12BBB40
5/8 19,500 3.79 58BBB40

 


STAINLESS STEEL, TYPE 316
CHAIN SIZE WORKING LOAD LIMIT WEIGHT PER FOOT IN POUNDS ESI PART # ‘s
1/4 2, 0.85 14SSG40
5/16 2,400 0.94 516SSG40
3/8 3,750 1.6 38SSG40
1/2 6,500 2.74 12SSG40
5/8 - - 58SSG40


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Grade 70 Transport Chain With Hook End


TRANSPORT CHAIN – Grade 70, yellow chromate finish

SIZE WORKING LOAD LIMIT IN POUDS APPROX. WT. EACH IN POUNDS ESI PART # ‘s
5/16 X 20′ 4,700 20.00 516SCG70BC20
3/8 X 20′ 6,600 31.00 38SCG70BC20
1/2 X 20′ 11,300 57.00 12SCG70BC20


TRANSPORT CHAIN – Grade 70, yellow chromate finish


6X19 FIBER CORE IPS (CHINESE)
SIZE WORKING LOAD LIMIT IN POUNDS FEET PER DRUM MINIMUM 1/2 DRUM WEIGHT FOOT IN POUNDS ESI PART # ‘s
1/4 3,150 800 400 0.63 14SCG70C
5/16 4,700 550 275 0.93 516SCG70C
3/8 6,600 400 200 1.41 38SCG70C
1/2 11,300 200 100 2.4 12SCG70C
5/8 15,800 100 - 3.75 58SCG70C

Also available in ASTM dimensions.


View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Swivel Hoist Hooks Grade 80

SWIVEL HOIST HOOKS – Grade 80 Alloy, Painted red with stainless steel latch

WORKING LOAD LIMIT IN POUNDS DIMENSIONS APPROX. WEIGHT EACH IN POUNDS ESI PART #’S (CARBON)
A B C D E F G H J K L M N
2 3.00 1.50 1.75 3.59 1.50 1.00 1.16 1.06 0.88 7.94 0.88 6.01 0.63 2.5 ASH2T
3 3.50 1.56 2.00 4.00 1.62 1.13 1.31 1.31 0.94 8.60 0.94 6.72 0.75 3.8 ASH3T
5 4.00 1.56 2.25 4.84 2.00 1.44 1.63 1.63 1.31 10.32 1.13 8.00 0.88 7.0 ASH5T
7 5.00 1.94 2.75 6.27 2.50 1.81 2.06 2.06 1.66 12.84 1.44 9.90 1.13 14.0 ASH7T
11 5.62 2.05 3.12 7.54 3.00 2.25 2.63 2.63 1.88 15.24 1.63 11.74 1.25 22.3 ASH11T
15 7.12 3.62 4.10 8.33 3.25 2.59 2.94 2.94 2.19 18.64 1.94 14.41 1.50 37.8 ASH15T

Working Load Limit applies only when the load is applied to the center of the saddle of the hook.
CAUTION: NEVER EXCEED THE WORKING LOAD LIMIT.

View this Chain Now at Elite Sales


Call (877) 833-0131 to Speak with ESI
Buy Wholesale Chain

Blue Alloy Chain Grade 100

Blue Alloy Chain Grade 100 - 9/32 Blue Alloy Chain Grade 100 - 5/16 Blue Alloy Chain Grade 100 - 3/8 Blue Alloy Chain Grade 100 - 1/2
9/32″ 5/16″ 3/8″ 1/2″
Blue Alloy Chain Grade 100
BLUE POWDER COATED ALLOY CHAIN – GRADE 100
SIZE IN INCHES WORKING LOAD LIMIT IN POUNDS FEET PER DRUM MINIMUM WEIGHT PER FOOT IN POUNDS
9/32 4,300 500 .75
5/16 5,700 500 1.13
3/8 8,800 400 1.48
1/2 15, 200 2.49

Blue Powder Coated Grade 100 Chain is heat treated with high strength chain that offers some advantages
just like grade 80 chain. It works faster and better while giving 25 extra working load limit. Suppose, if you
were using Grade 80 for the work load limit of 12, pounds, then Blue Powder Coated Grade 100 Chain
has been known for working load limit of 15, pounds. You can use it along with smaller other chains
that will make the work load simpler. Such type of product is known for abrasion resistance and comes with
the extended lifestyle. However, the chain needs 20 elongation for better work. It is known for the ability
to stretch down in the proper way, without the fear of getting broken down.

Features

  • Distinctive blue powder coat finish
  • Tempered alloy steel
  • It is pull tested to 2 1/2 times working load limit
  • Minimum elongation of 20
  • Fully hardened
  • Links embossed with grade
  • You also get the traceability code
  • Advantages of Using the Product

    Bending Resistance
    Such type of chain comes with 38 higher power of resistance as compared to the regular round-link
    chains of the same diameter. It offers good support and can withstand bending forces as compared to
    round-link chains

    Higher Design Factor
    The design is same as that of other grade chain products, but it comes with better workload factor and
    offers a design factor of 6:1 compared to G80.

    Color-Coated Corrosion Protection
    Due to the blue color powder coated finishing, it offers corrosion protection and is easy identifying.
    The product is recommended for overhead lifting and binder chain facility. However, you can use it, for
    other purposes, as well.

    Alternate Finishes

  • Shot blast
  • Galvanized
  • Self colored
  • Painted gray

    Technical Specifications

  • Hardness approx. 41 HRC
  • Nominal proof stress* 600N/mm2
  • Nominal breaking stress* 1200 N/mm2

  • View this Chain Now at Elite Sales


    Call (877) 833-0131 to Speak with ESI
    Buy Wholesale Chain

    General Information About Chain


    Because it has the ability to perform multipurpose duties, chain is widely used in all industry. Coupled with the unique ability to elongate before breaking giving the user sufficient time to replace before property damage or injury, it is the choice for lifting, securing, towing and pulling applications.

    Welded chain is manufactured in accordance to NACM and ASTM specifications in both graded and non-graded chains, With non-graded chains being used or non-technical applications where strength is not essential. Graded chains are generally marked with the grade and are suitable for many industry applications, including transport and lifting.

    Elite: Grade 28/30 Chain

    This welded chain is manufactured from low carbon steel, it is durable and economical in self-color, electro-galvanized and hot galvanized finishes. Stocked in both NACM and ASTM dimensions. This general utility chain is used in applications where high tensile strength is not required. Wide range of applications from agriculture, logging, securing, guard-rails and towing. Do not use for overhead lifting. Minimum elongation is 15. FINI5H: Self colored, electro galvanized, hot galvanized, Bright polished and epoxy coatings of various colors also avail-able. Packaged in drums, 1/2 drums, and reels. All proof coil chain is proof tested; proof test certificates are available on request. Industry name: PROOF COIL.

    Elite: Grade 43 Chain

    Manufactured of higher strength carbon steel to provide increased strength to weight ratio plus resistance to
    wear and abrasion. Applications include lumbering, construction, binding and securing. Industry name: HIGH
    TEST CHAIN

    Elite: Grade 70 Chain

    Load ratings for the Grade 70 chain include an average of 20 higher than that of Grade 43 chain, consequently
    a smaller size chain can be used for many jobs. Advantages include less weight, easier handling and more
    convenient storage. Higher strength makes the Elite Sales, Inc. Grade 70.

    Elite: Grade 80 Chain

    The only grade of chain made of high grade alloy steel designed for overhead lifting. Due to the high grade of
    alloy steel, our minimum elongation before breaking is 25 compared to the industry standard of 20. A complete line of alloy fittings are available to complement our chain. FINISH: Black lacquered, shot peened and hot
    galvanized.** Case hardened also available.

    Elite: Stainless Steel Chain

    Elite offers two types of stainless steel chain: Type 304 and 316, used wherever resistance to a corrosive environment or heat is required. Do not use for overhead lifting. Highly resistant to salt water and most acids. Due to
    the particular metallurgical structure of the base material, stainless steel chain resists high temperature.

    FAILURE TO FOLLOW IMPORTANT WARNINGS AND INSTRUCTIONS
    CAN RESULT IN SERIOUS INJURY OR DEATH!

    Refer to the General Warnings on page General Information on Chain.

    These warnings also apply to fittings. Only additional warnings and information are listed below.

    Never exceed the Working Load Limit of the chain.

    The Working Load Limit is the maximum load that should ever be applied to the chain, even when new and when the load is uniformly applied. Working Load Limit applies only to straight line pulls….

    Use only alloy chain for overhead lifting.

    Grade 80 alloy chain…

    Attachments must have at least the same Working Load Limit as the chain used.

    Hooks, links, shackles, etc…

    Keep out from under a raised load.

    Do not operate load over people…

    Avoid shock loads.

    Avoid impacting, jerking or swinging of load…

    Inspect products regularly.

    No product can keep operating at its rated capacity indefinitely…

    Destroy, rather than discard, items that have been judged defective.

    Chain that is not destroyed might be used again by someone not aware of the hazard.

    Chain Slings.

    Only grade 80 alloy chain can be used for overhead lifting…


    View this Chain Article Now


    Call (877) 833-0131 to Speak with ESI
    Buy Wholesale Chain

      Call (877) 833-0131 to Speak with ESI
      Buy Chain, Rigging Hardware and Strand